Tools

An economical option for safely and accurately tightening fasteners to proper torque specifications. With a simple gauge readout, the TW-1.2 is intuitive and easy to use, and applies up to 14 Nm of torque to any fastener or component with left or right-handed threads. Perfect for low-torque applications such as stem bolts, levers, and carbon fiber components. 3/8" drive for compatibility with all Park Tool sockets, bits, and crow feet. - 0 to 14 Newton meter (0 to 140 inch-pound) range - 3/8" drive - Reads and registers torque values for both left hand and right hand threading - Length: 11.5" (292 mm)

The BBP-AOS is used in conjunction with the BBP-1.2 Bottom Bracket Bearing Press Kit to extract press fit bottom bracket bearings, cups, and adaptors. The BBP-AOS utilizes an expanding collet and extractor cup system to safely remove bearings without requiring impact. Also included are eight installation drifts for pressing bearings into pre-installed cups. - 8 precision-machined extractor cups and 5 hardened collets for compatibility with most bearing IDs and bearing/cup ODs - 8 installation drifts for standalone bearing installation - Organized in a convenient storage case - Full list of compatible bearing inner/outer diameters found on instructions/parts diagram NOTE: The BBP-AOS requires the BBP-1.2 Bottom Bracket Bearing Press Set for use. The BBP-1.2 and BBP-AOS are also available as a complete set (part # BBP-2).

Disc brake rotors should be regularly checked for wear to ensure safety and performance. The DCA-1 installs onto most digital, dial, or vernier calipers (including the Park Tool DC-1) and features protruding contact points that allow measurement of the center of the braking surface, bypassing the unworn edge to ensure an accurate measurement. The conical end points of the DCA-1 can be used to measure center-to-center distances of bolt holes for calculating bolt circle diameter (BCD) of chainrings and cranks. - Compatible with most standard vernier, dial, and digital caliper designs

Park Shop Cone Wrenches are made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on hubs and other bearing assemblies. Their special Y-heads put more material where it's needed for greater strength. Most applications require several cone wrenches, so Park gives you a whole set, featuring 13mm - 24mm, 26mm and 28mm wrenches to suit your repair needs.

World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. Forged from chrome vanadium steel, chrome plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip.

Shop-quality, adjustable torque driver that limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The ATD-1.2 features all-metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at Park Tool's factory in Minnesota.

World-famous Park Tool quality wrapped up in a combination metric wrench. Features both open and 12-point two-way ratcheting box ends. Forged from chrome vanadium steel, chrome plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful!

The CRS-15EXT includes a tube and fitting to extend any CRS-15 to work on fork steering tubes up to 425mm.

Engineered for fit, function, and leverage, these L-shaped shop-quality Torx compatible wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Torx compatible drivers at each end - Includes T6, T8, T10, T15, T20, T25, T30, and T40 - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization

Professional quality T-Handle star-shaped wrench built for speed, efficiency, leverage and a perfect fit. - Carefully selected combination of Chrome Vanadium and S-2 tool steels - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Sliding T-handle creates increased leverage and multiple access positions

Park's BBT-32 is the perfect solution for the home mechanic installing and removing Shimano and ISIS Drive splined 20-tooth bottom bracket cups. Made from investment-cast steel, the BBT-32 utilizes a flat tooth profile to ensure maximum engagement with the bottom bracket cup and features 32mm wrench flats.

Park's Crank Puller is for removing crankarms on Shimano's splined, oversize, pipe-billet bottom brackets. It employs a long handle and a fine thread for the leverage and torque needed to remove tight arms. Park's unique rotating tip ensures smooth operation and long life. (The CCP-44 does not fit standard square or tapered bottom brackets.)

They always say, the right tool for the right job. Park's P-handled Torx Wrenches are available in T6, T8, T10, T15, T20, T25, T30 and T40 sizes. They feature offset handles made from durable nylon with a comfortable, ergonomic design. The wrenches are made of high-torque industrial steel for excellent durability.

Park's Needle Nose Pliers are professional quality, 6-inches long, and made from forged, heat-treated chromoly steel. For ease of use they have a hidden spring, cutting jaws and 5 different gripping and crimping areas. Plus, they have soft-touch, dual-density handles for an excellent grip.

Choose the perfect tool for the job with Park's P-Handled Hex Wrenches. These top-shelf Allen wrenches come with offset handles made from durable nylon in a comfortable, ergonomic design. They are made of chrome vanadium for exceptional durability. The long shafts feature Bondhus heads for accessing hard-to-reach bolts and the short ends are chamfered for extra grip and high-torque applications.

Park's Threadless-Fork Saw Guide ensures a straight, accurate cut on threadless carbon forks. Specially designed to accommodate wider, carbon specific saw blades, the SG-8 ensures a perfect cut every time. Slide on the guide, clamp it down and the specially shaped hardened-steel cutting slot guides your saw blade. And, the SG-8 Saw Guide ensures a straight, clean cut on fork steerer tubes up to 1-1/4-inches.

Park’s Shop Apron protects your clothes and provides large pockets to hold frequently needed tools. It’s made of heavy-duty, 7-ounce poly/cotton twill for comfort and durability.

Park Tool's CTP-4K includes four replacement chain tool pins and one 5/32" ball bearing. To replace the chain tool pin, unscrew the cap, and pull out the old pin. Use care not to lose the ball bearing beneath the pin. Install the new pin and replace the cap. Works with the CT-4.3, CT-4.2, CT-4, and CT-11

Park Tool's TS-RK is a complete rebuild kit for the TS-2 truing stand. It is complete with the most commonly replaced small parts and the instructions needed to get your stand back into top working condition. In addition to making the stand more accurate and reliable, once installed, the new parts also allow the stand to be readjusted much more easily, should it be thrown out of adjustment. This is a great addition to the older TS-2 stands. If your stand has silver-colored shaft collars, upgrade with the TS-RK. The TS-RK includes the following: • 1 - #211S Main Shaft • 4 - #749-1 Bearing Washer • 2 - #748-1 Needle Bearing • 2 - #209-2 Shaft Adjusting Collar • 1 - #229 Spring • 4 - #232-2 Split Nylon Bushing • 2 - #235-2 Split Nylon Bushing • 1 - #222-SR Right Caliper Spring • 1 - #222-SL Left Caliper Spring • 1 - Set of Installation and Adjustment Instructions

Park Tool's 752 Reamer and Spacer Set allows reaming of bottom bracket frame shells in the BB30 standard. The reamer is sized at 41.94mm. It is used with the HTR-1 Head Tube Reamer and Facer and a 750.2 Centering Cone (each sold separately). The set includes a spacer to stop the reaming depth.

Shop quality L-shaped, high torque industrial steel Torx compatible wrenches. Featuring chamfered tips, tight tolerances and a handy portable tool holder for easy access. Includes: T9, T10, T15, T20, T25, T27, T30 and T40.

These are the adaptors included with HHP-2, also available separately. Sold as a pair. The adaptors are stepped at 25.7mm, 29.7, and 32.8mm. - For replacement or retrofit to older bearing press tools - Adapts older HHPs to fit headcups for 1" and 1- 1/8" - Multi-step adapters fit most press fit cup applications

Park Tool offers premium-quality reamers for nearly any bicycle standard. The reamers below are designed to quickly, accurately, and precisely ream headtubes when used with Park's Head Tube Reamer (HTR), ensuring a perfect headset fit and prfoessional-quality bicycle build. Choose the correct reamer for your application using the following information: - 751.2: This reamer is sized to 30.1mm. This allows a 0.1mm interference fit when pressing the 30.2mm headset of the “Euro” one-inch standard. - 754.2: This reamer is sized to 33.9mm. The allows a 0.1mm interference fit when pressing the 34.0mm headset of the 1-1/8" standard. - 788: This reamer is sized to 43.95mm. It reams head tubes to accept “internal” headset cups with 44.05 - 44.10mm O.D. (1-1/8 ZS standard). It is used with Park Tool's 690-XL Facing Cutter and 750 Centering Cone. - 738: This reamer is sized to 52.1mm. It is used to ream head tubes using the 1-1/2" integrated headset standard. It is used with Park Tool's 690-XL Facing Cutter and 750.2 Centering Cone Adapter. - 789: This reamer is sized to 55.95mm. It is used to ream head tubes to accept “internal” headset cups with 56.00–56.10mm O.D. (1-1/2 ZS standard). It is used with Park Tool's 690-XXL Facing Cutter and #750 Centering Cone Adaptor. - 799: This reamer is sized to 47mm. It is used for cutting the lower head tube on frames using an IS47 bearing for a 1-1/4" integrated headset. It cuts a 45-degree bearing set shoulder.

- Brake holder features M5, M6 & passthrough holes for attaching all disc brake mounting styles as well as most rim brake caliper styles - 1-1/8" steerer tube features star nut for retaining top cap and spacers - 2" flared cone for compatibility with tapered steerer tubes - Compatible with 1-1/8" threadless stems only—not compatible with threaded headset/quill stem setups

Park Tool introduced the bicycle world to the 3-way hex wrench set over 30 years ago. Our 3-way wrenches fit perfectly in the palm of the hand and provide excellent leverage, making them a favorite of countless shop mechanics worldwide. AWS-3 FEATURES - 2mm, 2.5mm, and 3mm hex set - Wrenches made from industrial tool steel, through hardened and tempered for long life - Chamfered tips for a perfect fit

A handy tool designed to make installation and removal of bicycle electronic shifting wires and batteries quick and easy. The durable composite body features our iconic three-way wrench shape and prevents scratching of expensive components. Angled ends allow for safe installation and removal of Shimano Di2 E-tube EW-SD300; wires in tight spaces. Universal coin cell tool helps remove and install battery covers on SRAM AXS and other electronic accessories. - Compatible with Shimano Di2 E-tube, EW-SD300 wires (nominally 3 mm OD connector) - Not compatible with Shimano Di2 E-Tube EW-SD50 wires (nominally 5 mm OD connector) — use the Park Tool EWS-1

Park's Four-Sided Spoke Wrenches grip 4 sides of the spoke nipple so they offer an excellent grip and won't slip or round nipples when turning even the tightest spokes and/or aluminum nipples. These popular wrenches also have easy-to-hold vinyl-coated loop handles that are color-coded according to spoke size for easy identification. The loop handle makes them easy to hang on your tool board too.

With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The Park Tool TW-5.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). With a range of 2-14Nm, the TW-5.2 is designed for the lower torque settings that a shop or consumer would use for proper seat post, seat clamp and handlebar / stem applications. Comes with its own protective case.

Designed and built to remove and install Shimano direct mount chainring lockrings found on XTR 9120, XT 8120, MT900, and other Shimano direct mount systems. Precisely CNC machined from 6061 aluminum for a perfect fit and to prevent marring expensive parts. - Machined flat face for optimal lockring engagement - For lockrings with 41mm outside diameter and 16 notches - 36mm hex drive to be used with Park Tool TWB-36 Crow Foot and a torque wrench to properly measure torque - 6061 aluminum construction

Removes and installs crank caps on Shimano® Hollowtech II® cranks. Includes built in hook to lift the safety plate, speeding crank removal. Steel, investment cast body provides good leverage and includes an option to use with an 8mm hex wrench for removing seized caps.